We have 1000’s of used and new mcculloch chainsaw parts. We just bought out a large mcculloch dealer this summer and got lots of NOS chainsaw parts. We have lots of used mcculloch parts. Especially for common models like 10-10, pro mac, 10 series, super pro series, 610, power mac, timber bear and many many other models. I recently acquired a Power Mac 320 which is not in running condition. I would like to find the owners and parts manuals for this model. Does anyone know of any websites that I can possibly download these manuals from? View and Download McCulloch Power Mac 310 owner's manual online. Power Mac 310 Chainsaw pdf manual download. Also for: Power mac 320, Power mac 340, Power mac 330. Mcculloch Power Mac 310 Pdf User Manuals. View online or download Mcculloch Power Mac 310 Owner's Manual. Recent McCulloch Power Mac 310/320/330/340 Chain Saw Parts List-4 Manuals - 1 Low Price questions, problems & answers. Free expert DIY tips, support, troubleshooting help & repair advice for all Garden. NOS McCulloch Mac-Cat 2.1, Power Mac 310, Power Mac 320, Power Mac 330 Chainsaw Manual Oil Pump Rod 94540 $2.99 $2.99 NOS McCulloch Mac Cat, Power Mac 310, Power mac 320, Power Mac 330, Power Mac 340 Chainsaw Coil Mounting Screw 120112. NOS McCulloch Mac Cat, Power Mac 310, 320, 330, Chainsaw Starter Pawl Pin 216984 $1.99.
Related Articles
Mcculloch Power Mac 310 Manual
The McCulloch Power Mac 310 chain saw is a somewhat vintage model. It was new about the same time the first personal computers came on the market, in the mid 1980s. Like most chain saws, it has three carburetor adjustment screws, and chances are good that they need adjusting. It's a fairly simple matter to set the idle and low-speed screws, but setting the high-speed screw is challenging and shouldn't be attempted without a tachometer. Without one, it's simple to set the fuel mixture too lean and burn out the motor.
1
Remove the air box cover from the left side of the McCulloch Power Mac 310 chain saw by using a Phillips screwdriver to remove its single screw. The chain saw's left side is the side that is on your left when you operate the chain saw. Remove the air filter, and clean it with compressed air. If you can't clean it, then replace it.
2
Drain fuel from the chain saw's fuel tank, and replace it with fresh, high-octane gasoline mixed with two-cycle engine oil at a ratio of 40 parts gasoline to 1 part oil. Fill the fuel tank completely with the mixture. Otherwise, the engine might run too rich the next time you fill the tank.
3
Start the chain saw's engine, and let it warm up for about five minutes. If the carburetor is so far out of adjustment that the engine won't start, turn both the high-speed screw -- H -- and low-speed screw -- L -- clockwise as far as they will go, using a flat-head screwdriver, then turn them counterclockwise by 1 1/2 turns.
Mcculloch Power Mac 3204
Turn the idle screw -- I -- clockwise until the chain starts to spin, then turn it counterclockwise slightly. Adjust the screw to find the highest setting possible without making the chain spin. Check the setting by holding a digital tachometer over the spark plug. It should read between 2,700 and 2,900 rpm.
Mcculloch Power Mac 310 Manual Instructions5
Turn the low-speed screw clockwise until the engine begins to race, and make a note of that position of the screw. Turn the low-speed screw counterclockwise until the engine begins to stall, and note that position of the screw. The final setting is midway between those two positions. This adjustment may throw off the idle adjustment, and so resetting it may be necessary.
6
Engage the throttle, and while the saw is running at full speed, turn the high-speed screw clockwise until the engine races and the motor sounds thin. Turn the high-speed screw counterclockwise until the motor takes on a lustier gurgling sound without losing power. Check the engine speed with the digital tachometer. It should be fewer than 13,000 rpm. Uni mac model number uwn060t3vxu3001 manual.
It also makes sense to back up to optical disk as hard drive can fail, even exernal ones.If you do get a FW drive, I like to ones from. How to perform manual backup on mac. The cloning to a FireWire drive is a great way to insure that you can recover in the event of a disaster. Select your data, hit burn and Toast will then prompt you for the next disk until all that data is burned.Let me second Miriam's recommendation of SuperDuper. Insert a blank CD or DVD and drag your files right over to it, then hit 'burn' and let it do its job.There are programs like Roxio's Toast Titanium that will allow you to span that data over several disks without having to worry about the capacity.
7
Readjust both the low-speed screw and idle screw.
Things You Will Need
Tip
Warning
References (2)About the Author
Chris Deziel has a bachelor's degree in physics and a master's degree in humanities. Besides having an abiding interest in popular science, Deziel has been active in the building and home design trades since 1975. As a landscape builder, he helped establish two gardening companies.
After a few measurements were taken, and a few drafts were printed, and a few measurements were slightly changed, and a few more were printed, we ended up with a great solution!In the picture below you can see the old caps’ collared lugs, the new cap lugs with and without the collar. We ordered replacement capacitors, and worked on the rest of the unit as we waited for them to arrive. Mcintosh mac 4100 manual pdf. I noticed the older capacitors had a plastic collar around the lugs, preventing them from touching the chassis where they are mounted in the unit. The new capacitors had a huge risk of touching the chassis, which would be catastrophic.The best solution we came up with was to 3-D print a collar that would fit around the lug.
Photo Credits![]()
![]() Choose Citation Style
Deziel, Chris. 'How to Adjust the Carburetor on a McCulloch Chain Saw Model 310.' Home Guides | SF Gate, http://homeguides.sfgate.com/adjust-carburetor-mcculloch-chain-saw-model-310-101690.html. Accessed 25 August 2019.
Deziel, Chris. (n.d.). How to Adjust the Carburetor on a McCulloch Chain Saw Model 310. Home Guides | SF Gate. Retrieved from http://homeguides.sfgate.com/adjust-carburetor-mcculloch-chain-saw-model-310-101690.html
Deziel, Chris. 'How to Adjust the Carburetor on a McCulloch Chain Saw Model 310' accessed August 25, 2019. http://homeguides.sfgate.com/adjust-carburetor-mcculloch-chain-saw-model-310-101690.html
Note: Depending on which text editor you're pasting into, you might have to add the italics to the site name.
Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |